Enginetech ESL1148 is a centrifugally cast iron cylinder repair sleeve with 3.687 inch bore, 7.563 inch length, 3/32 inch wall, cataloged for 1957-1970 Dodge, International applications. It restores a damaged or over-bored cylinder to OE standard bore size without replacing the entire block.
Important Notes
- Sleeve is supplied with a semi-finished inside diameter; plan to remove at least 0.025 inch during final bore and hone to achieve the correct piston-to-wall clearance.
- Chamfered bottom outside diameter is intended to ease installation into the engine block; a light interference fit is typical and the block counterbore should be measured before pressing.
- Nominal wall thickness is 3/32 inch. Confirm the block counterbore diameter will accept the sleeve outside diameter before ordering.
- Sold individually; quantity required equals the number of cylinders being sleeved.
- Ships individually boxed and wrapped in rust-preventative paper.
| Part Number | ESL1148 |
| Bore Diameter | 3.687 in |
| Sleeve Length | 7.563 in |
| Wall Thickness | 3/32 in |
| Material | Cast Iron (Centrifugally Cast) |
| Finish | Semi-finished ID, chamfered bottom OD |
| OEM Cross-Refs | Melling:CSL1148 |
Vehicle Fitment
- 1957-1958 Dodge Coronet 5.3L 325ci V8 OHV
- 1957-1958 Dodge Custom 5.3L 325ci V8 OHV
- 1957-1958 Dodge Lancer 5.3L 325ci V8 OHV
- 1957-1958 Dodge Royal 5.3L 325ci V8 OHV
- 1957-1958 International A102 4.3L 264ci I6 OHV
- 1957-1958 International A110 4.3L 264ci I6 OHV
- 1957-1958 International A112 4.3L 264ci I6 OHV
- 1957-1958 International A120 4.3L 264ci I6 OHV
- 1957-1958 International A122 4.3L 264ci I6 OHV
- 1957-1958 International A130 4.3L 264ci I6 OHV
- 1957-1958 International A132 4.3L 264ci I6 OHV
- 1959 Dodge Coronet 5.3L 326ci V8 OHV
- 1959-1960 International B100 4.3L 264ci I6 OHV
- 1959-1960 International B102 4.3L 264ci I6 OHV
- 1959-1960 International B110 4.3L 264ci I6 OHV
- 1959-1960 International B112 4.3L 264ci I6 OHV
- 1959-1960 International B120 4.3L 264ci I6 OHV
- 1959-1960 International B122 4.3L 264ci I6 OHV
- 1959-1960 International B130 4.3L 264ci I6 OHV
- 1959-1960 International B132 4.3L 264ci I6 OHV
- ...and 6 additional applications
Enginetech cylinder sleeves are centrifugally cast engine block repair components available in a full range of bore diameters and lengths, supplied in standard 3/32 inch and 1/8 inch wall thicknesses. Centrifugal casting produces homogenous material throughout each sleeve for consistent hardness and machinability, and every sleeve is supplied with a semi-finished inside diameter that allows the machinist to remove at least 0.025 inch during boring and honing for a precision bore-to-piston fit. A chamfered bottom OD edge eases installation into the block, and each sleeve ships individually boxed and wrapped in rust-preventative paper for clean shelf storage. Enginetech also produces high-performance sleeves cast from a premium formula yielding higher hardness (293 BHN) and higher tensile strength (45,000 PSI) where the application demands it. Always verify bore diameter, sleeve length, and wall thickness against the damaged cylinder before ordering.
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
